Forgot Password
FaQ
| Frequently Asked Questions | ||||
|
These sander are designed for sanding all types of materials i.e. metals, wood, stone, plastics, etc. using abrasive designed for this purpose. Do not use these sanders for any other purpose than that specified without consulting the manufacturer or the manufacturer's authorized supplier.
01) What I should know before using the sander? • Always wear safety goggles to protect your eyes. • Oil daily for superior performance. • Wear face shield whenever tool is in operation.
02) What kind of air supply is required for these sanders? Only test and operate our sanders at 90 PSI/6.1 BAR maximum unless the tool is marked otherwise. Use recommended airline filters, regulators and lubricators.
03) How do I know what size back-up pad I should use? The size of the pads are marked on the bottom of the sander when the pad has been removed. The number is engraved on the shaft balancer.
04) Can I use a 5" back-up pad on a 6” sander or vice versa? No! The AirVANTAGE sanders are all precisely balanced to take only a certain size pad. If it is a 5" machine, it should always and only use a 5" back-up pad. This rule applies across the board for all AirVANTAGE Random Orbital Sanders.
05) How can I tell the difference between the 3/32" and the 3/16" orbits in the models? Visually, you can differentiate between the sanders by the throttle plate finish. Anodized throttle plate: 3/32" orbit Chrome throttle plate: 3/16" orbit You can also distinguish between the two by looking under the sander at the Shaft Balancer.
06) Why have two different orbits of 3/16" (5mm) and 3/32" (2.5mm)? 3/16" orbit gives a more aggressive cut for removing material such as bondo. More commonly used by the body shop repairs. 3/32" is for automotive painting application where fine sanding is needed or for applications where 3/16" orbit is found to be too aggressive. 3/32" orbit is commonly used in the furniture industry for fine sanding on dark stained finishes.
07) How do I distinguish between 10,000 and 12,000RPM Sanders? The RPM rating is engraved under the AirVANTAGE logo on the throttle plate.
08) Why does it seem as if my sander is operating at such a low power? Check if the speed control located under the air inlet is at the minimum or maximum air flow.
09) What should I do when the sander starts to make unusual sounds and vibration? • Check if you have the right size pad installed on your AirVANTAGE sander. Please check the FAQ to find out which pad is required for your sander. • The back-up pad might be worn, or deteriorated from over use. If material is nicked off of the pad, that will throw the sander off balance and cause unusual vibration. • If the sander has the correct size pad installed and is in good condition, you may want to take the AirVANTAGE sander in for service.
10) Where can I find the part listing for these sanders? • Random Orbital Part Listing and Diagram • 3-2/3" x 7" Orbital Part Listing and Diagram • 3" x 4" Orbital Part Listing and Diagram
11) Where can I send my AirVANTAGE sander for repairs? If your sander ever needs repairs, you can send it to the address below with freight prepaid for repair, along with a brief description the issues you have with the sander. NSW: PNEUMATIC EQUIPMENT REPAIR SALES AND SERVICE PTY LTD 117 RACECOURSE RD., RUTHERFORD NSW 2320 PH: 02 49326611 FAX: 02 49324107 EMAIL: sales@airtools.com.au WEB: www.airtools.com.au QLD: TOOLS 'R' US UNIT 1 / LOT 3 McPHAIL RD., COOMERA QLD 4209 PH: 07 55800554 FAX: 0755800564 QLD: ALL JACK AND AIRTOOLS BUILDING 640 ARCHERFIELD AIRPORT, ARCHERFIELD QLD 4108 PH: 07 32775678 FAX: 07 32775675 QLD: QME & SUPPLIES PTY LTD 44 ELVIN ST., PAGET QLD 4740 PH: 07 49539000 FAX: 07 49524060
12) How can I convert my AirVANTAGE sander from a non-vacuum model to a central-vacuum or self-generate model? The conversion can be easily done by installing a few parts on the non-vacuum model sander. Please refer to the appropriate tutorials for conversion: Non-Vacuum to Central Vacuum Tutorial |
